Archives
November 9, 2021 9:11 am
Published by dean
DESCRIPTION
THIS ITEM IS A NEW FLOOR SHIFTER BLANKING PLATE TO SUIT HQ - WB SERIES HOLDENS.
THIS IS A NON FACORY PART. INTENDED TO BE USED AS A “BOLT, OR SCREW ON” OPTION TO COVER AN UNUSED FLOOR SHIFTER HOLE, (WELDING NOT NECESSARY). THE BLANKING PLATE SIZE IS APPROXIMATELY 170mm long x 190mm wide, SUPPLIED WITHOUT MOUNTING HOLES, DUE TO POSSIBLE DIFFERENCES BETWEEN VEHICLES.
PLEASE NOTE- THIS LISTING IS FOR ONE SINGLE PLATE ONLY. A GREAT PIECE, IF YOUR CAR NEEDS THIS HOLE IN THE FLOOR COVERED.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
DESCRIPTION
THIS ITEM IS A SINGLE SMALL (upper) RE- MADE HEATER BLANK OFF PLATE TO SUIT ALL HK HT AND HG HOLDENS.
PLEASE NOTE- THIS LISTING IS FOR ONE SINGLE PLATE ONLY.
THIS ITEM WOULD BE A GREAT PIECE TO REPLACE YOUR UPPER HEATER PLATE, IF YOU HAVE ONE MISSING.
THESE PLATES SCREW OVER THE HOLES WHERE THE HEATER IS USUALLY POSITIONED ON THE FIREWALL. THIS PLATE SUITS THE UPPER HOLE.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A CUSTOM MADE PANEL TO SUIT A HK HT OR HG HOLDEN UTE. IT IS MADE TO FIT AND WELD OVER THE SPARE WHEEL DOOR OPENING TO DELETE THE DOOR. (SEE PICS).
THE PANEL IS MADE WITH A ROLL AT THE BOTTOM TO SUIT THE CONTOUR OF THE UTE BEAVER PANEL, AND THE TOP HAS A SLIGHT CREST IN THE CENTRE TO SUIT THE TRAY'S REAR PROFILE.
THIS PANEL WAS DESIGNED FOR REMOVAL OF YOU RUSTED SPARE WHEEL DOOR, OR IF YOU ARE GOING FOR A MODIFIED LOOK (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A RE- MADE SPARE WHEEL WELL DELETE PANEL KIT TO ALL HK HT OR HG SERIES HOLDENS.
THIS PANEL IS MADE MADE TO SUIT PEOPLE WHO WANT TO REMOVE THE SPARE WHEEL WELL IN THEIR CAR, OR JUST TO MATCH THE OTHER SIDE OF THE CAR. IT IS A MIRROR IMAGE PART TO THE L/H SIDE, CONSITING OF TWO PIECES (LIKE LHS). THIS IS A NON ORIGINAL PART, SO WILL REQUIRE SOME EXTRA MODIFICATION TO YOUR VEHICLE IN THE INSTALATION PROCESS, SO MAY NOT SUIT EVERYONES ABILITIES.
THESE ARE HAND FORMED USING MEASUREMENTS FROM ORIGINAL CARS FOR DIMENSIONS, ACCURACY AND TO RESEMBLE AN ORIGINAL PART AS MUCH AS POSSIBLE, SEE LAST PHOTOS FOR REFERENCE & LOCATION.
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE KIT ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
June 29, 2019 12:54 pm
Published by dean
THESE ITEMS ARE A 3 PIECE BOOT COMPARTMENT PANEL COVER SET, TO SUIT HK HT OR HG SERIES HOLDEN (MONARO COUPE, KINGSWOOD, BELMONT & PREMIER SEDAN BODY STYLES).
BEING NON- ORIGINAL PIECES, DESIGNED BY DEANO’S AS AN APPEARANCE PACKAGE, THIS KIT IS MADE WITH A SWAGED EDGE FOR A FACTORY LOOK. INTENDED TO BE SCREWED, OR BONDED IN PLACE.
THESE PANELS ARE HAND FORMED, AND TEST FITTED TO A SAMPLE BODYSHELL AS TEMPLATE FOR DIMENSIONS, ACCURACY. SEE PHOTOS FOR REFERENCE, LAST PHOTO SHOWS ONE INSTALLED (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE SET OF 3 PIECES ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
July 10, 2019 10:25 am
Published by dean
THIS ITEM IS A BOOT LID REPAIR PANEL, TO SUIT HK SERIES HOLDEN only (MONARO COUPE, KINGSWOOD, BELMONT & PREMIER SEDAN BODY STYLES). APPROPRIATE HOLES WOULD HAVE TO BE DRILLED TO SUIT MODEL.
INTENDED FOR REPAIRING A DAMAGED OR RUSTY HK BOOT LID.
THESE PANELS ARE HAND FORMED, AND TEST FITTED TO A SAMPLE BODYSHELL AS TEMPLATE FOR DIMENSIONS, ACCURACY. SEE PHOTOS FOR REFERENCE, LAST PHOTO SHOWS ONE INSTALLED (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PART ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
July 30, 2024 8:25 pm
Published by dean
THIS ITEM IS A BOOT LID REPAIR PANEL, TO SUIT HT & HG SERIES HOLDENS (MONARO COUPE, KINGSWOOD, BELMONT & PREMIER SEDAN BODY STYLES). APPROPRIATE HOLES WOULD HAVE TO BE DRILLED TO SUIT MODEL. BOOT LOCK HOLE WILL ALSO NEED FILING TO SUIT LOCK BARREL.
INTENDED FOR REPAIRING A DAMAGED OR RUSTY BOOT LID.
THESE PANELS ARE HAND FORMED, AND TEST FITTED TO A SAMPLE BODYSHELL AS TEMPLATE FOR DIMENSIONS, ACCURACY. SEE PHOTOS FOR REFERENCE, LAST PHOTO SHOWS ONE INSTALLED (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PART ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
March 1, 2023 10:01 pm
Published by dean
THESE ITEMS ARE A 2 PIECE FIREWALL SEAM REPAIR KIT (for LH passenger side), TO SUIT HK HT HG SERIES HOLDENS.
A COMMON AREA FOR RUST.
THESE PANELS ARE HAND FORMED, AND TEST FITTED TO A SAMPLE BODYSHELL AS TEMPLATE FOR DIMENSIONS, ACCURACY. PLEASE SEE PHOTOS FOR REFERENCE, AND LOCATION.
THESE PANELS WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE 2 PIECE KIT ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A RE- MADE SPARE WHEEL WELL PANEL TO SUIT HK HT OR HG SERIES HOLDENS (MONARO COUPE, KINGSWOOD, BELMONT & PREMIER SEDANS).
THIS PANEL IS MADE TO FIT UP TO, AND JOIN ON MOST FACTORY SEAMS.
THESE ARE HAND FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. I MAKE THESE WITH THE PROPER "CROWN" SHAPED BOTTOM, NOT FLAT. SEE PHOTOS FOR REFERENCE, LAST PHOTO SHOWS ONE INSTALLED (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A RE- MADE SPARE WHEEL WELL PANEL BOTTOM SECTION TO HK HT OR HG SERIES HOLDENS (MONARO & SEDAN).
THIS PANEL IS MADE MADE TO SUIT JUST THE LOWER AREA OF THE SPARE WHEEL PANEL, FOR THOSE THAT DON'T NEED A FULL PANEL.
THESE ARE HAND FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. I MAKE THESE WITH THE PROPER "CROWN" SHAPED BOTTOM, NOT FLAT. SEE LAST PHOTOS FOR REFERENCE & LOCATION.
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A RE- MADE SPARE WHEEL WELL SIDE PANEL (extends downwards off boot floor), TO SUIT ALL HK HT OR HG SERIES HOLDENS, INCLUDING MONARO, SEDAN, UTE, VAN, WAGON.
THIS PANEL IS MADE TO FIT UP TO, AND JOIN ON MOST FACTORY SEAMS.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
November 21, 2018 10:10 am
Published by ntechmedia
THIS ITEM IS A RE- MADE LOWER TAILGATE SEAL RETAINING CHANNEL REPAIR SECTION TO SUIT HK HT OR HG SERIES HOLDEN WAGON.
THIS IS A STRAIGHT PIECE APPROXIMATELY 500mm LONG.
THIS IS QUITE AN INVOLVED PART, WITH FINE FOLDS. I'VE MATCHED THE SECTION AS BEST AS POSSIBLE. MADE IN 2 PIECES SPOT WELDED TOGETHER.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
February 14, 2022 3:15 pm
Published by dean
THIS ITEM IS A RE- MADE LOWER TAILGATE SEAL RETAINING CHANNEL REPAIR SECTION TO SUIT HQ - Z SERIES HOLDEN WAGON.
THIS IS A STRAIGHT PIECE APPROXIMATELY 500mm LONG.
THIS IS QUITE AN INVOLVED PART, WITH FINE FOLDS. I'VE MATCHED THE SECTION AS BEST AS POSSIBLE. MADE IN 2 PIECES SPOT WELDED TOGETHER.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
THIS ITEM IS A RE- MADE LOWER TAILGATE SEAL RETAINING CHANNEL REPAIR SECTION TO SUIT HK HT OR HG SERIES HOLDEN WAGON.
THIS IS A STRAIGHT PIECE APPROXIMATELY 1 metre LONG.
THIS IS QUITE AN INVOLVED PART, WITH FINE FOLDS. I'VE MATCHED THE SECTION AS BEST AS POSSIBLE. MADE IN 2 PIECES SPOT WELDED TOGETHER.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
February 14, 2022 3:12 pm
Published by dean
THIS ITEM IS A RE- MADE LOWER TAILGATE SEAL RETAINING CHANNEL REPAIR SECTION TO SUIT HQ - Z SERIES HOLDEN WAGON.
THIS IS A STRAIGHT PIECE APPROXIMATELY 1 metre LONG.
THIS IS QUITE AN INVOLVED PART, WITH FINE FOLDS. I'VE MATCHED THE SECTION AS BEST AS POSSIBLE. MADE IN 2 PIECES SPOT WELDED TOGETHER.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A RE- MADE LOWER TAILGATE SEAL RETAINING CHANNEL REPAIR SECTION TO SUIT HK HT OR HG SERIES HOLDEN WAGON (LH SIDE).
THIS IS QUITE AN INVOLVED PART, WITH FINE FOLDS & CURVES. I'VE MATCHED THE SECTION AS BEST AS POSSIBLE. MADE IN 2 PIECES SPOT WELDED TOGETHER. THESE SIDE SPECIFIC 1/2 SECTIONS ARE DESIGNED TO OVERLAP SLIGHTLY IN THE CENTRE OF THE VEHICLE.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENSIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS MUCH AS POSSIBLE. (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE LH (PASSENGER SIDE) PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
