Archives
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A HAND FORMED REPLACEMENT BOOT FLOOR HUMP, TO SUIT HK HT AND HG HOLDENS, INCLUDING MONAROS, FACTORY FITTED WITH THE 10 BOLT SALISBURY DIFF. THIS PANEL WOULD BE USEFULL IF YOU ARE FITTING A 10 BOLT TO YOUR CAR, OR REPAIRING / REPLACING A FACTORY PIECE IN YOUR CAR.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
July 28, 2022 7:37 pm
Published by dean
THIS ITEM IS A 10 BOOT FLOOR HUMP INFILL PANEL TO SUIT HK HT AND HG HOLDENS, THAT WERE FACTORY FITTED WITH A SALISBURY TYPE DIFF. THIS PANEL WOULD BE USEFULL IF YOU WANT TO FILL IN THE “HUMP” PRESSING, WHEN USING A FUEL TANK BLANK OFF PANEL, OR USING A STANDARD FUEL TANK (instead of original humped tank). THIS IS NOT A FACTORY PART, AND I HAVE DESIGNED THIS PANEL TO BOLT IN BETWEEN THE FUEL TANK BLANKING PLATE, AND THE BODY (intended to be installed with sealer).
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS & ACCURACY (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:11 am
Published by ntechmedia
THIS ITEM IS A HAND FORMED REPLACEMENT BOOT FLOOR HUMP, TO SUIT HK HT AND HG HOLDENS, INCLUDING MONAROS, FACTORY FITTED WITH THE 10 BOLT SALISBURY DIFF. THIS PANEL WOULD BE USEFULL IF YOU ARE FITTING A 10 BOLT TO YOUR CAR, OR REPAIRING / REPLACING A FACTORY PIECE IN YOUR CAR.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
November 24, 2022 10:38 am
Published by dean
THIS ITEM IS A NEW REPRODUCTION OF THE LARGE CENTRE FUEL TANK COVER (ONE ONLY), TO SUIT HK HT AND HG MONARO GTS 327 AND 350 MODELS.
(I CAN ALSO MAKE A COMPLETE SET OF 3 25 GALLON TANK COVERS. PLEASE CONTACT ME FOR COST ETC. CUSTOMERS WILL NEED TO SEND ME A PAIR OF STANDARD COVERS TO MODIFY).
THESE ARE PRODUCED USING MY ORIGINAL SAMPLES.
DUE TO SIZE, THIS ITEMS WOULD BE SENT VIA COURIER.
THANKS....DEANO'S AUTO RESTORATIONS.
November 21, 2018 10:10 am
Published by ntechmedia
DESCRIPTION
THESE ITEMS ARE A PAIR NEW RE- MADE SPARE WHEEL MOUNTING BRACKETS, TO SUIT HK HT AND HG SERIES HOLDEN SEDAN & MONARO COUPE MODELS, WITH FACTORY FITTED 6" WIDE WHEELS.
THESE ARE LOCATED (WELDED) ON THE R/H REAR CHASSIS RAIL. THESE BRACKETS ARE MADE FROM THE SAME GUAGE STEEL AS ORIGINALS.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE. PLEASE SEE PHOTOS FOR REFERENCE & LOCATION. REFERENCE PHOTO SHOWS MY REPRODUCED BRACKETS SITTING NEXT TO ORIGINALS IN A CAR.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PAIR OF 2 PARTS ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 18, 2022 10:57 am
Published by dean
DESCRIPTION
THIS ITEM IS A RUST REPAIR SECTION TO SUIT THE FRONT EDGE OF THE BOOT FLOOR (FUEL TANK RECESS AREA) ON ALL HD & HR SERIES HOLDENS. THIS IS A STRAIGHT SECTION, MEASURING APPROXIMATELY 850mm LONG.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
DESCRIPTION
THIS ITEM IS A RUST REPAIR SECTION TO SUIT THE FRONT EDGE OF THE BOOT FLOOR (FUEL TANK RECESS AREA) ON ALL HK HT & HG SERIES HOLDENS. THIS IS A STRAIGHT SECTION, MEASURING APPROXIMATELY 850mm LONG.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
THIS ITEM IS A REPAIR PANEL TO SUIT THE REAR BEAVER CENTRE AREA OF THE HK HT & HG SERIES UTE & PANEL VAN.
THIS PART REPLACES THE EDGE THAT THE SPARE WHEEL DOOR SCREWS ON TO.
THESE ARE MADE FROM 1.2mm ZINC ANNEALED STEEL TO HELP PREVENT RUST.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
February 16, 2019 9:40 am
Published by dean
THIS ITEM IS A CLUTCH MASTER CYLINDER BLANK OFF PLATE TO SUIT HK HT AND HG SERIES HOLDENS.
THIS PLATE USES THE EXISTING BOLT HOLES FOR THE CLUTCH MASTER CYLINDER FOR ATTACHMENT, AS PER ORIGINAL. SEE SECOND PHOTO TO SEE FITTING LOCATION.
THE PLATE IS MADE FROM CORRECT GUAGE ZINC ANNEAL STEEL, FROM AN ORIGINAL HOLDEN PART AS A SAMPLE.
THE PART WILL BE DELIVERED IN AN ETCH PRIMER / RUST PREVENTITIVE COATING.
PLEASE NOTE- AS THIS IS A HAND MADE PART, PLEASE ALLOW UP TO 5 WORKING DAYS BEFORE IT LEAVES MY HANDS, DEPENDING ON STOCK LEVELS. PLEASE ASK IF YOU ARE UNSURE.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
December 16, 2021 1:55 pm
Published by dean
THESE ITEMS ARE A PAIR (2 of) OF CIRCULAR ENGINE BAY ACCESS COVERS TO SUIT ALL HD & HR SERIES HOLDENS.
THESE ARE MADE TO COVER THE HOLES AT THE REAR CORNER OF THE INNER SKIRTS, NEAR THE FIREWALL IN THE ENGINE BAY (SEE PICS FOR LOCATION).
THESE PARTS ARE NOT A FACTORY FITTED PIECE. THEY ARE DESIGNED TO BLOCK OFF AND TIDY UP THE LOOK OF THE 2 LARGE HOLES IN THE REAR OF THE ENGINE BAY. THEY GIVE AN AUTHENTIC APPEARANCE, AS THEY ARE HAND MADE FROM BODY STEEL WITH A SIMILAR MATCHING EDGE TO THE HEATER BLANK PLATES THAT I MANUFACTURE (SEE PICS).
THESE COVERS ARE MADE TO BE BONDED INTO POSITION WITH A FEW DOBS OF SIKAFLEX, URETHANE OR SIMILAR PRODUCT, DUE TO NO ACCESS FROM BEHIND. THE OUTWARD SWAGE ALSO HELPS LOCATE THE PLATE IN POSITION (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PAIR ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
November 21, 2018 10:10 am
Published by ntechmedia
THESE ITEMS ARE A PAIR (2 of) OF CIRCULAR ENGINE BAY ACCESS COVERS TO SUIT ALL HK HT AND HG HOLDENS.
THESE ARE MADE TO COVER THE HOLES AT THE REAR CORNER OF THE INNER SKIRTS, NEAR THE FIREWALL IN THE ENGINE BAY (SEE PICS FOR LOCATION).
THESE PARTS ARE NOT A FACTORY FITTED PIECE. THEY ARE DESIGNED TO BLOCK OFF AND TIDY UP THE LOOK OF THE 2 LARGE HOLES IN THE REAR OF THE ENGINE BAY. THEY GIVE AN AUTHENTIC APPEARANCE, AS THEY ARE HAND MADE FROM BODY STEEL WITH A SIMILAR MATCHING EDGE TO THE HEATER BLANK PLATES THAT I MANUFACTURE (SEE PICS).
THESE COVERS ARE MADE TO BE BONDED INTO POSITION WITH A FEW DOBS OF SIKAFLEX, URETHANE OR SIMILAR PRODUCT, DUE TO NO ACCESS FROM BEHIND. THE OUTWARD SWAGE ALSO HELPS LOCATE THE PLATE IN POSITION (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PAIR ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
April 4, 2023 10:51 am
Published by dean
THESE ITEMS ARE A PAIR (2 of) ENGINE BAY SKIRT INFILL PANELS (weld in) TO SUIT ALL HK HT AND HG HOLDENS.
THESE ARE AN APPEARANCE KIT, MADE TO SMOOTH OUT THE ENGINE BAY’S FACTORY PRESSED INDENTS AT EACH SIDE AT THE FRONT OF THE INNER SKIRTS.
PLEASE NOTE- THESE ARE NOT FACTORY ORIGINAL PARTS, AND WELD IN PANELS, WOULD ALSO REQUIRE RELOCATING THE BATTERY. (SEE PICS FOR LOCATION).
THESE PANELS WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PAIR ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
November 21, 2018 10:10 am
Published by ntechmedia
Deano's -THE ORIGINAL MAUFACTURER OF THE HQ - WB heater blank off plate.
THIS ITEM IS A HEATER BLANK OFF PLATE TO SUIT HQ THROUGH TO WB SERIES HOLDENS (WITHOUT AIR CONDITIONING )
THIS VERSION HAS PRESSED FINNS FOR ADDED STRENGTH AND APPEARANCE.
THESE PLATES ARE MADE OUT OF 1mm PANEL STEEL, & WITH SEVERAL SWAGE LINES AROUND THE EDGE, TO GIVE A FACTORY APPEARANCE, ADD REINFORCEMENT AND AID IN SEALING (SEE PICS).
THESE PANELS WERE NOT A FACTORY FITTED PART, THEY ARE MADE TO SUIT PEOPLE THAT WANT TO REMOVE THEIR HEATER BOX (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
DESCRIPTION
NEW FINNED STLYE HEATER PLATES!!!
THESE ITEMS ARE A PAIR OF RE- MADE HEATER BLANK OFF PLATES TO SUIT ALL HK HT AND HG HOLDENS.
THEY SCREW OVER THE HOLES WHERE THE HEATER IS USUALLY POSITIONED ON THE FIREWALL (SEE PICS FOR REFERENCE).
THESE PLATES ARE HAND FORMED WITH THE SWAGE LINES AROUND THE EDGE TO SEAT & AID IN SEALING ON THE RAISED LIP OF THE CAR'S FIREWALL, WHICH A FLAT PLATE CANNOT DO (SWAGE DEPTH MAY DIFFER SLIGHTLY TO AN ORIGINAL SET). THESE PARTS ARE MADE OFF AN ORIGINAL SET FOR ACCURACY, SO THEY RESEMBLE THEM WELL. THE LOWER PLATE HAS A FOLDED CREASE LINE, AS THE ORIGINAL, IT GOES TO THE BOTTOM, WHICH FITS THE SHAPE OF THE FIREWALL PROPERLY (NOT TRANSIT DAMAGE!!) PLEASE REFER TO LAST PHOTOS OF AN ORIGINAL FOR EXAMPLE.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THESE PANELS COME DELIVERED AS BARE STEEL, SEALED IN A CLEAR PROTECTIVE COATING TO PREVENT RUST.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION. THE LAST PHOTO IS A REFERENCE TO SHOW LOCATION.
THIS LISTING IS FOR ONE SET ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS
November 21, 2018 10:10 am
Published by ntechmedia
THIS ITEM IS A FLOOR HUMP SECTION TO SUIT A HK HT OR HG MONARO, OR ANY CAR IN THIS SERIES THAT WERE FACTORY FITTED WITH THE 4 SPEED SAGINAW GEARBOX. THIS HUMP WAS ORIGINALLY PRESSED INTO THE TRANSMISION TUNNEL / FLOOR, ON THE L/H SIDE FOR CLEARANCE OF THE SHIFTER LINKAGES.
THIS PANEL IS HAND FORMED USING AN ORIGINAL PART AS A TEMPLATE, FOR ACCURACY. IT WOULD BE USEFULL TO SOMEONE NEEDING TO REPLACE A RUSTED OUT SECTION OF THEIR EXISTING FLOOR HUMP, OR FOR SOMEONE WANTING TO FIT A SAGINAW GEARBOX TO THEIR CAR. IT JUST REQUIRES MARKING, AND CUTTING OUT YOUR OLD SECTION, AND WELDING THIS PANEL IN.
THIS PANEL IS PANEL IS A SLIGHTLY LESS EXPENSIVE OPTION WITHOUT THE CREASING TO DUPLICATE ORIGINAL. IT IS GREAT FOR DOING A GEARBOX CONVERSION. (SEE PICS) I HAVE THE SAGINAW FLOOR HUMP IN ANOTHER LISTING WITH THE CREASES TO TRY TO GIVE A MORE FACTORY LOOK, IF REQUIRED.
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
November 21, 2018 10:11 am
Published by ntechmedia
DESCRIPTION
THIS ITEM IS A FLOOR HUMP SECTION TO SUIT A HK HT OR HG MONARO, OR ANY CAR IN THIS SERIES THAT WERE FACTORY FITTED WITH THE 4 SPEED SAGINAW GEARBOX. THIS HUMP WAS ORIGINALLY PRESSED INTO THE TRANSMISION TUNNEL / FLOOR, ON THE L/H SIDE FOR CLEARANCE OF THE SHIFTER LINKAGES.
THIS PANEL IS HAND FORMED USING AN ORIGINAL PART AS A TEMPLATE, FOR ACCURACY. IT WOULD BE USEFULL TO SOMEONE NEEDING TO REPLACE A RUSTED OUT SECTION OF THEIR EXISTING FLOOR HUMP, OR FOR SOMEONE WANTING TO FIT A SAGINAW GEARBOX TO THEIR CAR. IT JUST REQUIRES MARKING, AND CUTTING OUT YOUR OLD SECTION, AND WELDING THIS PANEL IN.
THIS VERSION OF FLOOR HUMP I'VE MADE, HAS THE WRINKLES AND CREASES, SIMILAR TO THE FACTORY PRESSING, TO GIVE A MORE AUTHENTIC APPEARANCE WHEN FITTED (SEE PICS).
THESE ARE FORMED USING ORIGINAL PARTS AS TEMPLATES FOR DIMENTIONS, ACCURACY AND MADE TO RESEMBLE THE ORIGINAL PART AS CLOSE AS POSSIBLE (SEE PHOTOS FOR REFERENCE & LOCATION).
THIS PANEL WOULD COME DELIVERED IN A CLEAR PROTECTIVE COATING.
PLEASE LOOK AT PHOTOS TO SEE IF SUITABLE FOR YOUR APPLICATION.
THIS LISTING IS FOR ONE PANEL ONLY.
PLEASE NOTE- BECAUSE THESE ARE HAND MADE TO ORDER PANELS, PLEASE READ ALL TERMS & CONDITIONS.
THIS ITEM WOULD BE SENT VIA TRACKABLE POST OR COURIER.
THANKS... DEANO'S AUTO RESTORATIONS